反应釜网
不锈钢反应釜
不锈钢反应锅
不锈钢抛光反应釜
蒸汽加热不锈钢反应釜
外盘半管式加热不锈钢反应釜
多功能分散反应釜
不锈钢反应罐
电加热不锈钢反应釜
不饱和聚酯树脂设备
切片机
不锈钢发酵罐
填料系列
不锈钢储罐
储罐
螺旋板式换热器
高速分散机
换热器
塔器设备
结晶器
管式炉
招聘发布_Jobs
优秀的人才团队永远是构筑百年企业的基石,是推动企业持续发展的动力,是企业引领运动潮流的源泉。
您对我们充满梦想,我们对您充满期待......
在线留言_Order
欢迎你选购我们公司的产品!
请您将所需的产品情况填入下面的表格,我们将制定有效的可行性方案给您,我们收到你的订单后会在最短的时间内响应。
行业动态_News
反应釜>>行业动态
电加热反应釜设备维护办法
发布者:admin  日期:2016-05-11  点击:1290

电加热反应釜所有阀门使用时,应缓慢转动阀杆(),压紧密封面,达到密封效果。在关闭的时候不能用力过猛,以免损坏密封面。电加热反应釜的电气控制仪表应由专人操作,并按规定设置过载保护设施。电加热反应釜应安装在坚固、平整的工作台上,工作台高度根据使用情况来决定,设备与工作台四周一定要留有一定的空间,以便安装与后期维修。

Electric heating reactor allvalves should be used, should be slow to turn the valve stem (needle), pressthe cover, to achieve the sealing effect. Can not be forced to close theclosure of the fierce, so as not to damage the sealing surface. The electricalcontrol instrument for electric heating reactor shall be operated by hand, andthe overload protection facilities shall be set up in accordance with theregulations. Electric heating reactor should be installed in a rugged, flat onthe work table, the use of a high level of work in accordance with thesituation to decide, equipment and the work station must be left around acertain space, so that the installation and maintenance of the late.

电加热反应釜安装时要求传动轴与地水平面垂直,不垂直度倾斜度也不得大于设备总高度,设备本身在各工艺接管上的自备件,反应釜安全阀,都必须按反应釜的要求配备。电加热反应釜安装完毕后要检查各连接部件及传动部位牢固可靠性,各连接管道、管口、密封件与整机做气密试验,要无泡、冒、滴、漏现象.

Electric heating reactorinstallation requirements drive shaft and horizontal vertical, verticalinclination also shall not be greater than the total height of the equipment,equipment itself in the process pipe self-contained pieces, reactor safetyvalve must according to the requirements of the reaction kettle with the.Electric heating reactor is installed to check the the connection parts andtransmission parts and strong reliability, the connecting pipe, nozzle, asealing piece and a machine to do air tightness test, no bubble, run, drip,leak phenomenon.

 

电加热反应釜应严格按产品铭牌上标定的工作压力和工作温度操作使用,以免造成危险,严格遵守产品使用说明书中关于冷却、注油等方面的规定,做好设备的维护和保养。

Electric heating reactorshould strictly according to product nameplate on the calibration work pressureand temperature operation, so as to avoid danger, strict compliance with theproduct specification on cooling, oil and other provisions, do a good job inthe maintenance of the equipment.

 

电加热反应釜开机前减速机注入机械油,打开电机防护罩用手转动风叶来检查有无卡怠现象,电加热反应釜搅拌桨是否有刮壁现象,清理釜内污物后,方可开机。空车运转0分钟无较大常噪音、振动,方可正式投料生产。

Electric heating reactor(www.gfanyingfu.com) boot speed reducer oil into the machine, open the motor protection cover with ahand rotating blades to check whether the card idle phenomenon, the electricheating reactor stirring paddle whether there are scratches the wall, clean thedirt inside the kettle, boot. Running empty 0 minutes without large noise andvibration can be used, the official feed production.

文章来源:http://www.gfanyingfu.com/news.asp?lt=322
[返回] [打印]
公司:无锡联盛石化装备制造有限公司 Copyright © www.gfanyingfu.com 反应釜网 All reserved. 
联系人:周锡军 先生 电话:0510-85918899 0510-85912299 手机:13606183220 15306183220 传真:0510-85917799 地址:江苏无锡市滨湖区胡埭工业园龙胆路18号
无锡联盛石化装备制造有限公司专业生产电加热反应釜等设备的专业厂家,价格实惠,欢迎咨询! 技术支持:优易网